Minrry Pneumatic and Electro-Pneumatic Bench Vocational Education Training Equipment Mechatronics Training Equipment

Pneumatic and electro-pneumatic bench Double-sided mobile workstation allows the assembly and operation of the various components without the use of tools (components equipped with quick assembly system)
-     1* Rolling table dimension between length 1200 mm, height 1700 mm and depth 800 mm minimum.
- 1* extruded and adonized aluminum plate of dimension between 1080 mm length and 680 mm depth minimum with the possibility of fixing the electrical components on both sides.
- 2* cabinet with a minimum of four drawers and locks 
- 1* cable guide
- 1 x power supply unit for mounting frame 220V AC- 24 VDC/ 4A minimum with minimum 6 outputs
- 1 x silent lubricated compressor for classroom use: protected by pressure switch and safety valve                                                                                                                                                           
-  Supply voltage 230V/50HZ
- Operating pressure 7 bar minimum                                                                            
- Suction flow rate 40 L/MIN minimum        
- Tank volume 9 L minimum                                                                           
- Outlet with pressure regulator, pressure gauge and quick coupler

 
Pre-actuator for manual and mechanical pressurization
 
-  2 push-button operated 3/2 NC spool valves
- 2 Push-button operated 3/2 NO dispensers
- 1 3/2 NC valve operated by emergency stop button
- 4 Distributors FC 3/2 NC roller-operated
- 2 NC 3/2 directional control valves operated by retractable roller
- 1 Switch operated 3/2 NC bistable valve
- 1 Push button operated 5/2 directional control valve
- 1 5/2-way valve with two-position selector switch
- 1 Closed center 5/3 valve operated by hook-in lever
Pneumatically operated pre-actuator
 
- 1 Pneumatically operated 3/2 NC monostable spool valve, 3/2 NC.
- 2 Pneumatically operated 5/2 monostable spool valves
- 2 Pneumatically operated 5/2 bistable valves

 
Signal processing, flow control and blocking
 
- 1 logic gate "OR".
- 1 "OR" circuit selector switch
- 1 "AND" logic gate
- 1 "AND" circuit selector switch
- 2 unidirectional flow throttles
- 1 Quick exhaust valve
- 1 Adjustable pneumatic timer with positive output
- 2 Flow regulators with pilot operated check valve
- 1 bi-directional flow restrictor
- 1 Sequence valve
Cylinders
-     2 Single-acting spring return cylinders
- 1 Double-acting cylinder with magnetic piston and elastic damping
- Double acting magnetic piston cylinder with adjustable pneumatic damping

 
Electro dispensers
- 1 Solenoid valve, 3/2-way monostable NC (24 VDC coil with LED indicator)
- 1 Solenoid valve, 3/2 bistable (24 VDC coil with LED indicator)
- 2 Solenoid valves, 5/2 bistable (24 VDC coil with LED indicator)
- 2 Solenoid valves, 5/2 monostable (24 VDC coil with LED indicator)
- 1 Solenoid valve, 5/3 closed center (24 VDC coil with LED indicator)
- 1 Vacuum generator by suction effect with suction cup
- Control modules/sensors
- 1 ON/OFF switch
- 1 Emergency stop push button (electric)
- 1 Set of electrical inputs (Box with 3 NO-NC pushbuttons)
- 1 Set of 3 relays (3 NO-3 NC, 24VDC coil)
- 1 Indicator (Indicators, ringer)

- 1 Set of 2 timer relays (2 NO- 2 NC)
- 1 Electrical connection terminal block
- 4 Magnetic detectors type Reed
- 2 Static magnetic detectors
- 1 Inductive sensor
- 1 Capacitive sensor
- 1 Photoelectric detector
- 4 Electric limit switch
- 1 Electrical contact pressure switch
- Accessories
- Set of 10 "T" Connectors Ø 4mm
- Set of 10 plastic caps Ø 4mm
- Set of 10 "Y" connectors Ø 4mm
- 1x 4 mm safety laboratory cable set (color red and blue) consisting of at least 80 cables
-  all pneumatic components must be equipped with Ø 4mm quick couplings


development thinking, and improve practical ability and actual operation ability, so that students after graduation can directly production practice, shorten the past when they graduate students practical ability weak defect, so as to adapt to requirements of modern measurement and control.
This training system not only for students, but also for industrial electrical, mechanical and electrical integration engineering, electrical and mechanical equipment installation, power electrical and electronic equipment installation, automation processing, regulation and control technology and technical personnel, for machinery manufacturing and electrical engineer training, the process and the process management electrical engineer training is the same.
If there is no sensor, automation production will be very difficult, therefore, sensor technology is main technology to improve productivity .
This sensor training system is designed to make students realize sensor control technology in automation system of importance and learn to select appropriate sensor in application.
Factory sensor training system enable students understand different types of sensor's working principle and use method.

II.Technical paramter
1.Input power:~220V±10% 50Hz
2.Work environment: temperature -10ºC~+40ºC  humidity <85%(25ºC) 
3. Whole capacity:<0.2KVA
4. Weight<280Kg
5. Safety protection: with voltage leakage protection, current leakage protection, meet national standard.
6.Aluminum base panel with hanging box

III.The bench contains the following components:
Input dispositive including:

• Potentiometer (carbon slide, winded with slider)
• NTC thermistor
• Thermocouple (K , J or T)
•  Temperature sensor with integrated circuit
• Photoconductor cell
• Photovoltaic cell
• Phototransistor
• Photodiode PIN
• Deformation gauge
• Air flow sensor
• Air pressure sensor
• Inductive proximity sensor
• Hall effect sensor
• Tachymetric generator
• Hygrometric generator
• Ultra-sound receiver

• Heat element
• DC motor
• Electro-valve
• Ultra sound transmitter
• Relay, solenoid
• Counter/clock with light-emitting diode

• 3 electronic circuit (comparator / adder / integrator)
• Amplifier with gain and offset adjusting
• Measure amplifier
• AC current amplifier
• 40 kHz oscillator
• 40 kHz filter
• Low-pass filter with switchable time constant
• Full wave stabilizer for precision
• Sampling and maintain circuit
• Voltage/frequency and frequency/voltage converter
• Current/voltage and voltage/current converter
• 2 oscillator circuit (RC and Wien bridge)
• Power amplifier

Each element is equipped by connection terminals

Power supply delivering all needed power for different devices

4. Complete experiment
(1) cognitive experiment of various sensors
(2) amplifier band gain and offset correction experiment
Service

We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.

Certificate

Our products takes ISO9001 product management system.